If the size of the package so requires, the minimum outer dimensions shown in Figure 3.4.8.1 may be
reduced to be not less than 50 mm x 50 mm provided the mark remains clearly visible. The minimum
width of the line forming the diamond may be reduced to a minimum of 1 mm. The symbol "Y" shall
remain in approximate proportion to that shown in Figure 3.4.8.1.

Packages containing dangerous goods bearing the mark shown in 3.4.8 with or without the additional
labels and marks for air transport shall be deemed to meet the provisions of section 3.4.1 as
appropriate and of sections 3.4.2 to 3.4.4 and need not bear the mark shown in 3.4.7.

Packages containing dangerous goods in limited quantities bearing the mark shown in 3.4.7 and
conforming with the provisions of the ICAO Technical Instructions, including all necessary marks and
labels specified in Parts 5 and 6, shall be deemed to meet the provisions of section 3.4.1 as appropriate
and of sections 3.4.2 to 3.4.4.

Use of overpacks

For an overpack containing dangerous goods packed in limited quantities, the following applies:
Unless the marks representative of all dangerous goods in an overpack are visible, the overpack shall
be:
– marked with the word “OVERPACK”. The lettering of the “OVERPACK” mark shall be at
least 12 mm high. The mark shall be in an official language of the country of origin and also, if
that language is not English, French or German, in English, French or German, unless
agreements, if any, concluded between the countries concerned in the transport operation
provide otherwise; and
– marked with the marks required by this Chapter.
Except for air transport, the other provisions of 5.1.2.1 apply only if other dangerous goods which are
not packed in limited quantities are contained in the overpack and only in relation to these other
dangerous goods.

In advance of carriage, consignors of dangerous goods packed in limited quantities shall inform the
carrier in a traceable form of the total gross mass of such goods to be consigned.

(a) Transport units with a maximum mass exceeding 12 tonnes carrying dangerous goods packed
in limited quantities shall be marked in accordance with 3.4.15 at the front and at the rear
except when the transport unit contains other dangerous goods for which orange-coloured plate
marking in accordance with 5.3.2 is required. In this latter case, the transport unit may display
the required orange-coloured plate marking only, or both the orange-coloured plate marking in
accordance with 5.3.2 and the marks in accordance with 3.4.15.
(b) Containers carrying dangerous goods packed in limited quantities, on transport units with a
maximum mass exceeding 12 tonnes, shall be marked in accordance with 3.4.15 on all four
sides except when the container contains other dangerous goods for which placarding in
accordance with 5.3.1 is required. In this latter case, the container may display the required
placards only, or both the placards in accordance with 5.3.1 and the marks in accordance with
3.4.15.
The carrying transport unit need not be marked, except when the marks affixed to the
containers are not visible from outside this carrying transport unit. In this latter case, the same
marks shall be affixed at the front and at the rear of the transport unit.

The marks specified in 3.4.13 may be dispensed with, if the total gross mass of the packages
containing dangerous goods packed in limited quantities carried does not exceed 8 tonnes per
transport unit.

The marks specified in 3.4.13 shall be the same as the one required in 3.4.7, except that their
minimum dimensions shall be 250 mm × 250 mm. These marks shall be removed or covered if no
dangerous goods in limited quantities are carried.

3.5

DANGEROUS GOODS PACKED IN EXCEPTED QUANTITIES

Excepted quantities

Excepted quantities of dangerous goods of certain classes, other than articles, meeting the provisions
of this Chapter are not subject to any other provisions of ADR except for:
(a) The training requirements in Chapter 1.3;
(b) The classification procedures and packing group criteria in Part 2;
(c) The packaging requirements of 4.1.1.1, 4.1.1.2, 4.1.1.4 and 4.1.1.6.
NOTE: In the case of radioactive material, the requirements for radioactive material in excepted
packages in 1.7.1.5 apply.

Dangerous goods which may be carried as excepted quantities in accordance with the provisions of
this Chapter are shown in column (7b) of Table A of Chapter 3.2 list by means of an alphanumeric
code as follows:
 

Code

Maximum net quantity per inner packaging (in grams for solids

and ml for liquids and gases)

Maximum net quantity per outer packaging (in grams for solids and ml for liquids

and gases, or sum of grams and ml in the case of mixed packing)

E0

Not permitted as Excepted Quantity

E1

30

1000

E2

30

500

E3

30

300

E4

1

500

E5

1

300

 

For gases, the volume indicated for inner packagings refers to the water capacity of the inner

receptacle and the volume indicated for outer packagings refers to the combined water capacity of all
inner packagings within a single outer packaging.

 

Where dangerous goods in excepted quantities for which different codes are assigned are packaged
together the total quantity per outer packaging shall be limited to that corresponding to the most
restrictive code.

Excepted quantities of dangerous goods assigned to codes E1, E2, E4 and E5 with a maximum net
quantity of dangerous goods per inner packaging limited to 1 ml for liquids and gases and 1 g for
solids and a maximum net quantity of dangerous goods per outer packaging which does not exceed
100 g for solids or 100 ml for liquids and gases are only subject to:
(a) The provisions of 3.5.2, except that an intermediate packaging is not required if the inner
packagings are securely packed in an outer packaging with cushioning material in such a way
that, under normal conditions of carriage, they cannot break, be punctured, or leak their
contents; and for liquids, the outer packaging contains sufficient absorbent material to absorb
the entire contents of the inner packagings; and
(b) The provisions of 3.5.3.
 

Packagings

Packagings used for the carriage of dangerous goods in excepted quantities shall be in compliance
with the following:
(a) There shall be an inner packaging and each inner packaging shall be constructed of plastic
(with a minimum thickness of 0.2 mm when used for liquids), or of glass, porcelain, stoneware,
earthenware or metal (see also 4.1.1.2) and the closure of each inner packaging shall be held
securely in place with wire, tape or other positive means; any receptacle having a neck with
moulded screw threads shall have a leak proof threaded type cap. The closure shall be resistant
to the contents;
(b) Each inner packaging shall be securely packed in an intermediate packaging with cushioning
material in such a way that, under normal conditions of carriage, they cannot break, be
punctured or leak their contents. For liquid dangerous goods, the intermediate or outer
packaging shall contain sufficient absorbent material to absorb the entire contents of the inner
packagings. When placed in the intermediate packaging, the absorbent material may be the
cushioning material. Dangerous goods shall not react dangerously with cushioning, absorbent
material and packaging material or reduce the integrity or function of the materials. Regardless
of its orientation, the package shall completely contain the contents in case of breakage or
leakage;
(c) The intermediate packaging shall be securely packed in a strong, rigid outer packaging
(wooden, fibreboard or other equally strong material);
(d) Each package type shall be in compliance with the provisions in 3.5.3;
(e) Each package shall be of such a size that there is adequate space to apply all necessary marks;
and
(f) Overpacks may be used and may also contain packages of dangerous goods or goods not
subject to the requirements of ADR.
Previous Matter Next Matter

adrbook.com - Copyright all rights reserved. © 2015-2018