Tests for packages

The complete package as prepared for carriage, with inner packagings filled to not less than 95% of
their capacity for solids or 98% for liquids, shall be capable of withstanding, as demonstrated by
testing which is appropriately documented, without breakage or leakage of any inner packaging and
without significant reduction in effectiveness:
(a) Drops onto a rigid, non-resilient flat and horizontal surface from a height of 1.8 m:
(i) Where the sample is in the shape of a box, it shall be dropped in each of the following
orientations:
- flat on the base;
- flat on the top;
- flat on the longest side;
- flat on the shortest side;
- on a corner;
(ii) Where the sample is in the shape of a drum, it shall be dropped in each of the following
orientations:
- diagonally on the top chime, with the centre of gravity directly above the point
of impact;
- diagonally on the base chime;
- flat on the side;
NOTE: Each of the above drops may be performed on different but identical packages.
(b) A force applied to the top surface for a duration of 24 hours, equivalent to the total weight of
identical packages if stacked to a height of 3 m (including the sample).

 

For the purposes of testing, the substances to be carried in the packaging may be replaced by other
substances except where this would invalidate the results of the tests. For solids, when another
substance is used, it must have the same physical characteristics (mass, grain size, etc.) as the
substance to be carried. In the drop tests for liquids, when another substance is used, its relative
density (specific gravity) and viscosity should be similar to those of the substance to be carried.

Marking of packages

Packages containing excepted quantities of dangerous goods prepared in accordance with this Chapter
shall be durably and legibly marked with the mark shown in 3.5.4.2. The first or only label number
indicated in column (5) of Table A of Chapter 3.2 for each of the dangerous goods contained in the
package shall be shown in the mark. Where the name of the consignor or consignee is not shown
elsewhere on the package this information shall be included within the mark.

Excepted quantities mark

Figure 3.5.4.2

Excepted quantities mark
* The first or only label number indicated in column (5) of Table A of Chapter 3.2 shall be
shown in this location.
** The name of the consignor or of the consignee shall be shown in this location if not shown
elsewhere on the package.
The mark shall be in the form of a square. The hatching and symbol shall be of the same colour, black
or red, on white or suitable contrasting background. The minimum dimensions shall be 100 mm x 100
mm. Where dimensions are not specified, all features shall be in approximate proportion to those
shown.

 

Use of overpacks

Use of overpacks
For an overpack containing dangerous goods packed in excepted quantities, the following applies:
Unless the marks representative of all dangerous goods in an overpack are visible, the overpack shall
be:
– marked with the word “OVERPACK”. The lettering of the “OVERPACK” mark shall be at
least 12 mm high. The mark shall be in an official language of the country of origin and also, if
that language is not English, French or German, in English, French or German, unless
agreements, if any, concluded between the countries concerned in the transport operation
provide otherwise; and
– marked with the marks required by this Chapter.
The other provisions of 5.1.2.1 apply only if other dangerous goods which are not packed in excepted
quantities are contained in the overpack and only in relation to these other dangerous goods.

Maximum number of packages in any vehicle or container

The number of packages in any vehicle or container shall not exceed 1 000.

Documentation

If a document or documents (such as a bill of lading, air waybill or CMR/CIM consignment note)
accompanies(y) dangerous goods in excepted quantities, at least one of these documents shall include
the statement "Dangerous Goods in Excepted Quantities" and indicate the number of packages.

4

Packing and tank provisions

4.1

USE OF PACKAGINGS, INCLUDING INTERMEDIATE BULK CONTAINERS (IBCs) AND LARGE PACKAGINGS

General provisions for the packing of dangerous goods in packagings, including IBCs and large packagings

NOTE: For the packing of goods of Classes 2, 6.2 and 7, the general provisions of this section only
apply as indicated in 4.1.8.2 (Class 6.2), 4.1.9.1.5 (Class 7) and in the applicable packing instructions
of 4.1.4 (P201 and LP200 for Class 2 and P620, P621, IBC620 and LP621 for Class 6.2).

Dangerous goods shall be packed in good quality packagings, including IBCs and large packagings,
which shall be strong enough to withstand the shocks and loadings normally encountered during
carriage, including trans-shipment between cargo transport units and between cargo transport units
and warehouses as well as any removal from a pallet or overpack for subsequent manual or
mechanical handling. Packagings, including IBCs and large packagings, shall be constructed and
closed so as to prevent any loss of contents when prepared for transport which might be caused under
normal conditions of transport, by vibration, or by changes in temperature, humidity or pressure
(resulting from altitude, for example). Packagings, including IBCs and large packagings, shall be
closed in accordance with the information provided by the manufacturer. No dangerous residue shall
adhere to the outside of packagings, IBCs and large packagings during carriage. These provisions
apply, as appropriate, to new, reused, reconditioned or remanufactured packagings and to new, reused,
repaired or remanufactured IBCs, and to new, reused or remanufactured large packagings.

Parts of packagings, including IBCs and large packagings, which are in direct contact with dangerous
goods:
(a) shall not be affected or significantly weakened by those dangerous goods;
(b) shall not cause a dangerous effect e.g. catalysing a reaction or reacting with the dangerous
goods; and
(c) shall not allow permeation of the dangerous goods that could constitute a danger under normal
conditions of carriage.
Where necessary, they shall be provided with a suitable inner coating or treatment.
NOTE: For chemical compatibility of plastics packagings, including IBCs, made from polyethylene
see 4.1.1.21.

Unless otherwise provided elsewhere in ADR, each packaging, including IBCs and large packagings,
except inner packagings, shall conform to a design type successfully tested in accordance with the
requirements of 6.1.5, 6.3.5, 6.5.6 or 6.6.5, as applicable. The packagings for which the test is not
required are mentioned under 6.1.1.3.
Previous Matter Next Matter

adrbook.com - Copyright all rights reserved. © 2015-2018