Additional provisions for goods of Class 2

Refillable receptacles shall bear the following particulars in clearly legible and durable characters:
(a) the UN number and the proper shipping name of the gas or mixture of gases, as determined in
accordance with 3.1.2.
In the case of gases classified under an N.O.S. entry, only the technical name1 of the gas has to
be indicated in addition to the UN number.
In the case of mixtures, not more than the two constituents which most predominantly
contribute to the hazards have to be indicated;
(b) for compressed gases filled by mass and for liquefied gases, either the maximum filling mass
and the tare of the receptacle with fittings and accessories as fitted at the time of filling, or the
gross mass;
 
1 Instead of the technical name the use of one of the following names is permitted:
- for UN No. 1078 refrigerant gas, n.o.s: mixture F1, mixture F2, mixture F3;
- for UN No. 1060 methylacetylene and propadiene mixtures, stabilized: mixture P1, mixture P2;
- for UN No. 1965 hydrocarbon gas mixture, liquefied, n.o.s.: mixture A or butane, mixture A01 or butane,
mixture A02 or butane, mixture A0 or butane, mixture A1, mixture B1, mixture B2, mixture B, mixture C
or propane;
- for UN No. 1010 Butadienes, stabilized: 1,2-Butadiene, stabilized, 1,3-Butadiene, stabilized.
 
(c) the date (year) of the next periodic inspection.
These particulars can either be engraved or indicated on a durable information disk or label attached
on the receptacle or indicated by an adherent and clearly visible mark such as by printing or by any
equivalent process.
NOTE 1: See also 6.2.2.7.
NOTE 2: For non refillable receptacles, see 6.2.2.8.

 

Special marking provisions for radioactive material

Each package shall be legibly and durably marked on the outside of the packaging with an
identification of either the consignor or consignee, or both. Each overpack shall be legibly and
durably marked on the outside of the overpack with an identification of either the consignor or
consignee, or both unless these marks of all packages within the overpack are clearly visible.

For each package, other than excepted packages, the UN number preceded by the letters "UN" and the
proper shipping name shall be legibly and durably marked on the outside of the packaging. The
marking of excepted packages shall be as required by 5.1.5.4.1.

Each package of gross mass exceeding 50 kg shall have its permissible gross mass legibly and durably
marked on the outside of the packaging.

Each package which conforms to:
(a) a Type IP-1 package, a Type IP-2 package or a Type IP-3 package design shall be legibly and
durably marked on the outside of the packaging with "TYPE IP-1", "TYPE IP-2" or "TYPE IP-
3" as appropriate;
(b) a Type A package design shall be legibly and durably marked on the outside of the packaging
with "TYPE A";
(c) a Type IP-2 package, a Type IP-3 package or a Type A package design shall be legibly and
durably marked on the outside of the packaging with the distinguishing sign used on vehicles
in international road traffic2 of the country of origin of design and either the name of the
manufacturer or other identification of the packaging specified by the competent authority of
the country of origin of design.

Each package which conforms to a design approved under one or more of paragraphs 1.6.6.2.1,
5.1.5.2.1, 6.4.22.1 to 6.4.22.4 and 6.4.23.4 to 6.4.23.7 shall be legibly and durably marked on the
outside of the package with the following information:
(a) the identification mark allocated to that design by the competent authority;
(b) a serial number to uniquely identify each packaging which conforms to that design;
(c) "Type B(U)", "Type B(M)" or "Type C", in the case of a Type B(U), Type B(M) or Type C
package design.

Each package which conforms to a Type B(U), Type B(M) or Type C package design shall have the
outside of the outermost receptacle which is resistant to the effects of fire and water plainly marked by
embossing, stamping or other means resistant to the effects of fire and water with the trefoil symbol
shown in the figure below.
 
2 Distinguishing sign of the State of registration used on motor vehicles and trailers in international road traffic,
e.g. in accordance with the Geneva Convention on Road Traffic of 1949 or the Vienna Convention on Road Traffic of
1968.,
 
Basic trefoil symbol with proportions based on a central circle of radius X.
The minimum allowable size of X shall be 4 mm.
 

Where LSA-I or SCO-I material is contained in receptacles or wrapping materials and is carried under
exclusive use as permitted by 4.1.9.2.4, the outer surface of these receptacles or wrapping materials
may bear the mark "RADIOACTIVE LSA-I" or "RADIOACTIVE SCO-I", as appropriate.

In all cases of international carriage of packages requiring competent authority approval of design or
shipment, for which different approval types apply in the different countries concerned by the
shipment, marking shall be in accordance with the certificate of the country of origin of the design.

Special marking provisions for environmentally hazardous substances

Packages containing environmentally hazardous substances meeting the criteria of 2.2.9.1.10 shall be
durably marked with the environmentally hazardous substance mark shown in 5.2.1.8.3 with the
exception of single packagings and combination packagings where such single packagings or inner
packagings of such combination packagings have:
- a quantity of 5 l or less for liquids; or
- a net mass of 5 kg or less for solids.

The environmentally hazardous substance mark shall be located adjacent to the marks required by
5.2.1.1. The requirements of 5.2.1.2 and 5.2.1.4 shall be met.

The environmentally hazardous substance mark shall be as shown in Figure 5.2.1.8.3.
Figure 5.2.1.8.3
 
 
Environmentally hazardous substance mark
 
The mark shall be in the form of a square set at an angle of 45° (diamond-shaped). The symbol (fish
and tree) shall be black on white or suitable contrasting background. The minimum dimensions shall
be 100 mm x 100 mm and the minimum width of the line forming the diamond shall be 2 mm. If the
size of the package so requires, the dimensions/line thickness may be reduced, provided the mark
remains clearly visible. Where dimensions are not specified, all features shall be in approximate
proportion to those shown.
NOTE: The labelling provisions of 5.2.2 apply in addition to any requirement for packages to bear
the environmentally hazardous substance mark.

 

Lithium battery mark

Previous Matter Next Matter

adrbook.com - Copyright all rights reserved. © 2015-2018